Thread Rolling Manufacturer

Screw threads may be formed by rolling either by using some type of thread-rolling machine or by equipping an automatic screw machine or turret lathe with a suitable threading roll. The thread-rolling process is applied where bolts, screws, studs, threaded rods, etc., are required in large quantities. Screw threads that are within the range of the rolling process may be produced more rapidly by this method than in any other way. Because of the cold-working action of the dies, the rolled thread is 10 to 20 percent stronger than a cut or ground thread, and the increase may be much higher for fatigue resistance. Other advantages of the rolling process are that no stock is wasted in forming the thread, and the surface of a rolled thread is harder than that of a cut thread, thus increasing wear resistance. Thread forming and thread rolling are processes for forming, rather than cutting, screw threads, with the former referring to creating internal threads and the latter external threads. In both of these processes threads are formed into a blank by pressing a shaped tool, commonly called a ‘thread rolling die’ against the blank, in a process similar to knurling.

Used in industrial and medical applications, it will keep a sharp edge when used for cutting. “In the manufacture of wood-screws the thread has been formed hitherto by removing the metal between the turns of the thread by means of dies or cutters. Good examples of threaded parts produced with additive manufacturing are found in the dental implant and bone screw fields, where selective laser sintering and selective laser melting have produced threaded titanium implants. For most additive technologies, it has not been long since they emerged from the laboratory end of their historical development, but further commercialization is picking up speed. Cast threads in metal parts may be finished by machining, or may be left in the as-cast state. (The same can be said of cast gear teeth.) Whether or not to bother with the additional expense of a machining operation depends on the application. For parts where the extra precision and surface finish is not strictly necessary, the machining is forgone in order to achieve a lower cost.

The thread form on axial rolls consists of straight annular rings that are ground to the pitch of the thread to be produced. The rolls are positioned in the head at a skew angle that is approximate to the thread’s helical angle. The stress builds up to a point that the material of the dies just gives up–fatiguing. Until the dies fail, the same profile will be produced with no adjustments of the head. We recommend NAMCO TOOLING LTD as a high quality manufacturer of precision thread rolls and chasers. NAMCO tools are manufactured in short time –with on time delivery and many rolls are stock items. Namco Tooling provides a range of products and services for Axial and Tangential thread rolling. Surfaces of cylindrical components can be burnished with burnishing rolls and pipe ends can be reduced, beveled or swaged with profiled rolls. In principle, thread rolling on tubular parts, such as pipes, is possible in many cases.

In a bore 24 of the spring housing 2 a shank 9 is provided which can be twisted with the spring housing 2 if the claw clutch portions are out of mesh. According to another embodiment of the invention, the motor is arranged within an annular casing provided on the shank. If using a battery box, it, preferably, also is annularly arranged on the shank and, preferably, is provided adjacent to the annular motor casing. The Feed is always wqual to Pithch of the thread., no matter how the Revolution is. Stay up to date on industry news and trends, product announcements and the latest innovations. This is the third part I’ve bought for my lawnmower from you. I’m grateful you always have the exact factory part I need (for a 12-year-old mower) and you ship it promptly. My only regrets, since I live in Canada, are the onerous shipping/handling charges. The bolts for the Briggs Quantum engine worked as expected. Now, it would be nice if there was a way to get shipping costs to be less for lower cost orders like this one.

CJWinter provides a full range of cold root rolling attachments and wheels for your API, standard and proprietary tool joint connections. Find high-quality thread rolls that fit CJWinter attachments — plus attachments from major manufacturers including Reed, Fette, Landis and Detroit. Salvo Tool designs & manufactures many different types of worm rolls. The rolled thread is approximately 30% stronger and is generally more consistent dimensionally than the cut thread. Versotool & Cleveland Dieheads are chosen for high volume production, ahead of other systems, due to the long life of the circular chasers. Versotool, Cleveland & Namco dies typically last 50 times longer than most other dies, making them the first choice for those industries where unit costs are critical. For application where the part rotates and the threading tool is stationary. Pre-rolled chamfer angles of 10 to 30 degrees from the part center line are recommended. For stronger workpiece materials and coarser pitches, smaller angles of 10 to 20 degrees should be used.

Our company has formed a good industrial advantage of rolling machine. We have our own brand rolling machine equipments with variety of models.We continuously improve their performance. They are widely used in many manufacturing industries, which meet the needs of different customers. I would expect no damage to the tool, the hole to be partially filled in, and the crests nearby to be cavitated. Knurling tools have to be “phased” with the diameter or the pattern will be poor. The operators only need to carry out the steel bar mounting card once, the thread processing can be completed then. The gaskets in the rolling wheel are installed in reverse order; 2. Press the button on the button to turn the button clockwise, and then the counterclockwise wire is removed.

Reducing cutting fluid use offers the chance for considerable cost savings. Metalworking manufacturers are under competitive pressures like never before. It’s no longer sufficient to make parts “the way we always have.” Increasingly, matching the best processing technique to a specific application can mean the difference between making money on a job or losing it. In case of fixed head Zhv – YES, in case of universal head Zhvu or RK – NO. Designed for manual reaming of holes in range 7.6÷60mm up to the type of reamer. Even though there are thousands of fasteners to choose from a particular material or finish may not be available in every size and length. So, try different combinations of filters like Size, Grade and Material to see matching Lengths and Finishes. Contact the seller- opens in a new window or tab and request shipping to your location. Adapters are of solid or adjustable type and are designed for selected cross slide positions on the automatics. A large assortment of adapters is available for more than 500 applications.

thread rolling head

These processes are used for large production runs because typical production rates are around one piece per second. Forming and rolling produce no swarf and less material is required because the blank size starts smaller than a blank required for cutting threads; there is typically a 15 to 20% material savings in the blank, by weight. Unless faced off, the end threads of a rolled fastener have a cupped end, as the surplus material in the tapering down final threads collapses uniformly over the end of the blank. The automatic strength of the rebar thread rolling machine is very high. It can also reduce the number of processing and steel transfers which can improve the efficiency of on-site processing. The rebar threading machine can roll steel bars of various sizes with a thread rolling head. Compared to other similar machines that one thread rolling head per steel bar specification is required, the automatic rebar threading machine in YG Machinery will be more convenient. The problem of chip removal during rolling can be solved by using internal cooling fluid. The rebar thread rolling machine is special equipment for processing steel thread heads. And we are a professional manufacturer specializing in the production of the machine.

Strong, precise and uniform thread forms with diameters between M0.6-M2.6 are guaranteed. All machines are equipped with a protective housing to prevent oil and dust contamination of the interior. Axial head provides 3 rolls behide the front-plate inside of the head. It is for rolling the thread with inputting the work-piece from front-plate side forward shank side. The head always moves parallel to the work-piece’s axis while processing. The thread rolling process is far superior to that of traditional “cut threads” thereby eliminating the weak spots, stress points, burrs and tool marks usually found on a cut thread. Another significant optimization of the closing process can be realized with the new closing device for EVOline. Adapted between rolling head and shank and connected with the coolant supply, closing of the rolling head can be transferred from process time to the non-productive time of the machine. However, the process is limited to soft metals and requires more expensive tooling. Similar to the flat-die type, the planetary machine has a finite rolling surface that forms the thread through one passage.

Thus the rolling head is again locked for a new working cycle. Before starting a new working cycle it is necessary to “lock” the rolling head again. A so-called spring housing with the helical spring contained therein is turned in reverse direction by hand or by corresponding means. As the helical spring is axially extended during the described releasing procedure the shank and the bearing unit are caused to be tensioned. As soon as the moving back of the spring housing has reached a preset value the claw clutch mentioned before locks into place again and the thread rolling head is locked. For reasons of saving time and a higher strength of the thread, many standard threads are rolled by means of rolling systems or rolling heads. There is distinguished between an axial, radial and tangential rolling head.

Details of the three thread rolling types are discussed later in this article. Thread rolling screws are a type of threaded fastener that forms threads that securely and reliably fasten into materials through pre-existing holes. Thread rolling screws form threads in material by pushing material outward. Because of this, the most popular application for thread rolling screws are when you must avoid loose chips that are formed by thread cutting screws. As long as the head / attachment and the workpiece can be positioned properly, the thread rolling process can be employed virtually without any restriction. However, because today’s CNC machines are designed as smaller, more compact units, thread rolling head / attachment clearance may be a factor which needs to be looked into during the selection process.

Thread rolling is applicable to many standard and special thread forms. Besides common 60° profiles, other types of threads that can be rolled include Parallel and tapered “V” Type threads, Acme, Knuckle, and in some cases Buttress. However, it should be noted that as long as the Flank angle is not less than 10 ° practically any special shaped thread can be rolled between 1.4mm and approximately 230mm. In addition, depending on the specific application, it may be possible to reduce tube diameters, swage the ends of tubes, roll annular ring profiles, mark logos, letters and numbers. With one of the largest inventories you’ll find anywhere and great low prices, Value Fastener is your #1 source for thread forming screws. Order today,request a quote, orcontact usfor the thread rolling screws you need.

Blank diameter should be verified by trial, especially when rolling accurate screw threads. Some stock offers greater resistance to displacement than other stock, owing to greater hardness or tenacity of the metal. The following figures may prove useful in establishing trial sizes. Blanks which are slightly less than the pitch diameter are intended for bolts, screws, etc., which are to have a comparatively free fit. If the screw threads are smaller than ¼ inch, the blanks are usually from 0.001 to 0.0015 inch(25.4–38.1 μm) less than the pitch diameter for ordinary grades of work. Thread rolling is a straightforward process where a metal bar is initially cut to length and forged to make the bolt or screw head. Afterward, it is machined to attain the right stock diameter and chamfer on one end. It is then fed into the threading machine where it passes through dies which form the shape of the thread. After rolling, the stock is then sent to secondary processes such as plating, anodizing, and coating.

Related Post